Factory Supplier Qsfp+Optical Transceiver for Multimode Om3 Max Distance 100m, Om4 Max 150m.

• Support Network: Ethernet
• Information content: Data
• Certification: ISO
• Condition: New
• Transceiver Module: Typical 10.3 GB/S
• Bend Radius: 3 Cm
• Model NO.: SUN-QSFP-SR4
• Output Logic Level High Noise: Max. Vcc
• Output Logic Level Low: Min 0
• Transport Package: Paper Box
• Trademark: SUN & logo
• Origin: China
• HS Code: 8517622990
• Production Capacity: 90, 000-120, 000 Pieces/Mth

Product Description

Product Description

SUN-QSFP-SR4 Optical Transceiver

Sun Telecom's SUN-QSFP-SR4 series optical transceiver is a 4-channel, pluggable, parallel, fiber-optic QSFP+ transceiver for 40 Gigabit Ethernet applications. This transceiver is a high performance module for short-range multi-lane data communication and interconnects applications. The optical interface uses a 12 fiber MTP (MPO) connector. It integrates four data lanes in each direction with 40 Gbps bandwidth. Each lane can operate at 10.3125 Gbps up to 100m using OM3 fiber or 150m using OM4 fiber.

Features
      1. 4 independent full-duplex channels
      2. 4 channels 850nm VCSEL array
      3. 4 channels PIN photo detector array
      4. Up to 10.3125Gbps data rate per channel
      5. MPO optical connector
      6. Maximum link length of 100m on OM3 fiber and 150m on OM4 fiber 
      7. Maximum power consumption 1.5W
      8. DDM Function
      9. Compatible with ROHS
      10. Compatible with QSFP+ MSA
      11. Operating temperature
          Non-industrial: 0 ~ +70°C
          Industrial: -40 ~ +85°C 

Applications
 

      1. Interconnection of Infiniband-based SDR, DDR and QDR 

      2. Datacom/Telecom switch & router connections

Pin Assignment and Description

Top Side Viewed From Top                 Bottom Side Viewed from Bottom
Figure 2: Electrical Pin-out Details
Pin Definition

PIN	Logic	Symbol	Name/Description	Notes
1		GND	Ground	1
2	CML-I	Tx2-	Transmitter Inverted Data Input
3	CML-I	Tx2+	Transmitter Non-Inverted Data Input
4		GND	Ground	1
5	CML-I	Tx4-	Transmitter Inverted Data Input
6	CML-I	Tx4+	Transmitter Non-Inverted Data Input
7		GND	Ground	1
8	LVTLL-I	MODSEIL	Module Select	2
9	LVTLL-I	ResetL	Module Reset	2
10		VccRx	+3.3V Power Supply Receiver
11	LVCMOS-I/O	SCL	2-Wire Serial Interface Clock	2
12	LVCMOS-I/O	SDA	2-Wire Serial Interface Data	2
13		GND	Ground	1
14	CML-O	Rx3+	Receiver Non-Inverted Data Output
15	CML-O	Rx3-	Receiver Inverted Data Output
16		GND	Ground	1
17	CML-O	Rx1+	Receiver Non-Inverted Data Output
18	CML-O	Rx1-	Receiver Inverted Data Output
19		GND	Ground	1
20		GND	Ground	1
21	CML-O	Rx2-	Receiver Inverted Data Output
22	CML-O	Rx2+	Receiver Non-Inverted Data Output
23		GND	Ground	1
24	CML-O	Rx4-	Receiver Inverted Data Output	1
25	CML-O	Rx4+	Receiver Non-Inverted Data Output
26		GND	Ground	1
27	LVTTL-O	ModPrsL	Module Present
28	LVTTL-O	IntL	Interrupt	2
29		VccTx	+3.3 V Power Supply Transmitter
30		Vcc1	+3.3 V Power Supply
31	LVTTL-I	LPMode	Low Power Mode	2
32		GND	Ground	1
33	CML-I	Tx3+	Transmitter Non-Inverted Data Input
34	CML-I	Tx3-	Transmitter Inverted Data Input
35		GND	Ground	1
36	CML-I	Tx1+	Transmitter Non-Inverted Data Input
37	CML-I	Tx1-	Transmitter Inverted Data Input
38		GND	Ground	1

Notes:

1. Module circuit ground is isolated from module chassis ground within the module.
2. Open collector should be pulled up with 4.7k - 10k ohms on host board to a voltage between 3.15V and 3.6V.

Optical Interface Lanes and Assignment
The optical interface port is a male MPO connector. The four fiber positions on the left as shown in Figure 3, with the key up, are used for the optical transmit signals (Channel 1 through 4). The fiber positions on the right are used for the optical received signals (Channel 4 through 1). The central four fibers are physically present.

Figure 3 Optical Receptacle and Channel Orientation
Transmit channels: 1 2 3 4. Unused position: x x x x. Receiver channels: 4 3 2 1

Absolute Maximum Ratings

Parameter	Symbol	Min	Max	Units
Storage Temperature	Tst	-20	85	ºC
Input Voltage	Vin	-0.3	Vcc+0.3	V
Power Supply Voltage	Vcc	-0.3	3.6	V
Relative Humidity (non-condensation)	RH	5	95	%

Recommended Operating Conditions and Power Supply Requirements

Parameter		Symbol	Min	Typical	Max	Units
Operating Temperature	Non-industrial	Tc	0		70	ºC
	Industrial	Tc	-40		85	ºC
Power Supply Voltage		Vcc	3.13	3.3	3.47	V
Date Rate Each Lane		fd		10.3	10.5^(1)	Gbps
Power Dissipation		Pm			1.5	W
Fiber Bend Radius		Rb	3			CM

Note:

1. Up to 12.5Gbps may be supported.

Electrical Characteristics
The following electrical characteristics are defined over the Recommended Operating Environment unless otherwise specified.

Parameter	Symbol	Min	Typical	Max	Units
Differential Input Impedance	Zin	90	100	110	Ohm
Differential Output Impedance	Zout	90	100	110	Ohm
Differential Input Voltage Amplitude	ΔVin	300		1100	mVp-p
Differential Output Voltage Amplitude	ΔVOut	500		800	mVp-p
Skew	Sw			300	ps
Bit Error Rate	BER			E-12
Input Logic Level High	VIH	2		VCC	V
Input Logic Level Low	VIL	0		0.8	V
Output Logic Level High	VOH	VCC-0.5		VCC	V
Output Logic Level Low	VOL	0		0.4	V

Note:

1. BER=10^-12; PRBS 2^[email protected].

2.  Differential input voltage amplitude is measured between TxnP and TxnN.
3.  Differential output voltage amplitude is measured between RxnP and RxnN.

Optical Characteristics

Parameter	Symbol	Min	Typical	Max	Units	Notes
Transmitter
Center Wavelength	λC	840	850	860	nm
RMS Spectral Width	Δλ			0.65	nm
Average Launch Power Each Lane	Pavg	-7.5		2.5	dBm
Difference in Launch Power between any Two Lanes (OMA)				4	dBm
Extinction Ratio	ER	3			dB
Peak Power Each Lane				4	dBm
Transmitter and Dispersion Penalty (TDP) Each Lane	TDP			3.5	dB
Transmitter Eye Mask Definition {X1, X2, X3, Y1, Y2, Y3}		{0.23, 0.34, 0.43, 0.27, 0.35, 0.4}				Hit Ratio = 5x10-5
Average Launch Power OFF Transmitter Each Lane				-30	dB
Receiver
Center Wavelength	λC	840	850	860	Nm
Minimum Average Received Power Each Lane				-9.5	dBm
Receiver Reflectance	Rr			-12	dB
Maximum Average Received Power Each Lane				2.4	dBm
Stressed Receiver Sensitivity (OMA) Each Lane				-5.4	dBm	1
Peak Power Each Lane				4	dBm
LOS Assert	LOSA	-30			dBm
LOS De-Assert-OMA	LOSD			-7.5	dBm
LOS Hysteresis	LOSH	0.5			dB

Notes:
1. Measured with conformance test signal at TP3 for BER = 10e^-12

Ordering Information

Model	Name	Description
SUN-QSFP-40G-SR4	Optical Transceiver	QSFP+ SR4, 40Gbps; 100m on OM3 fiber and 150m on OM4 fiber; Non-industrial grade
SUN-QSFP-40G-SR4-I	Optical Transceiver	QSFP+ SR4, 40Gbps; 100m on OM3 fiber and 150m on OM4 fiber; Industrial grade

Related Products

Company Profile